New 1Gbps connection; router only lets 100Mbps
Landon Veitch last edited by
So I recently upgraded my Comcast connection to 1Gbps down/35Mbps upload.
From the modem directly, speedtest showcases those speeds
Once I add the router to the mix, both wireless and hard wire connections all drop to 100Mbps down/5Mbps upload
I have swapped out the cable from modem to router with a new Cat6 cable - no luck.
I called Comcast back twice and had them ensure everything was good with signal, modem profiles, house wiring, etc. - no luck
I have software rev 2.6.1, fully updated as of today (Feb 8, 2017).
Any ideas on why this would be happening?
UI-Gunars last edited by
Jason Etheridge last edited by
I have almost the same situation. I upgraded to AT&T Fiber and connected directly to the gateway, I get between 800-900 Mbps. Connected to the Amplifi router either wired or wireless, I get 100 Mbps. Can you shed some light on why? I turned on Hardware NAT based on another article but that didn't seem to help.
UI-Brett last edited by
Stefan Nobbe last edited by
I am having the same issue where my speedtest maxes out around 200Mbps up/down on Verizon FIOS Gigabit while I am running in bridge mode.
I have proactively sent the support info and email as directed to the other posts, any ideas on why I am not seeing higher throughput? The Verizon test from my modem identifies gigabit speeds.
Mark Chensky last edited by
@jayson-knight I echo this statement. I use Wave 1G up/down and cannot achieve over 300 on wireless sitting 3 feet from the router.
Derek Saville last edited by
Out of curiosity, in the app if you go on the Family tab, under Client Details for the device, what does it show for MIMO (i.e. 2x2) and Rx Bitrate?
@jayson-knight 300 Mbps is definitely not a limit. I am routinely achieving 400 Mbps at home with single Amplifi router and Linux laptop behind thick brick wall. In lab environment, we usually observe ~460 Mbps download speed.
Eric Kavalauskas last edited by Eric Kavalauskas
I'm having similar issues. My internet is 600mb/s. I'm hard-wired to the Amplifi router but can't get anything greater than 100mb/s. I submitted my information.
@landon-veitch Do you still have this problem?
@eric-kavalauskas According to support info, your Internet port is working in 100 Mbps mode instead of 1 Gbps. For some reason, link mode autonegotiation has made such decision. Most probably your cable or modem port is faulty.
You can try to:
- Replace cable
- Put simple gigabit ethernet switch between your modem (or whatever you have coming from ISP side) and Amplifi
UI-Karlis last edited by UI-Karlis
Has anybody seen speed limited to 100 Mbps also with v2.4.3 firmware version (before more recent v2.6.* versions)?
@landon-veitch This is not a new issue. Apparently they have been trying to address this for some time. I have been asking about this for the longest time as well. Similar situation. Not sure if they feel this is important. It is for me because I pay for the most speed and don't get it with this hardware. Can the team advise and provide information on this? Is this software related or simply the router just doesn't have hardware to support these speeds?
UI-Gunars last edited by UI-Gunars
@andres-betts Are you experiencing a 100 Mbps cap over a wired connection? The issue we're investigating here is WAN link not being negotiated to 1 Gbps.
Neil Chaplin last edited by
@jayson-knight I was told by the amplifi support "161mbps from the mesh points on 5ghz is normal speed"
@ubnt-gunars I have experienced this although not this only. I have experienced nothing over 100Mbps in the AP antennas. The usual cap when using the main unit is around 450Mbps. All on this WIFI. When wired to the main unit I get the full 940Mbps that Xfinity offers. This is an old issue. I worked on this with a couple of techs at Amplifi to isolate the problem, but was told in the end that this is something that they were not putting effort into because it was not widespread.
Can you please make an effort to at least arrive at an answer? If the unit is "not" meant to go over 450Mbps over wifi because of physical constraints, it is ok. I will wait for a next version of the product. If this is software related and fixable through coding, then I can help troubleshoot.
A Former User last edited by
@jayson-knight Are you positive the device you're testing from is connected to a mesh point? The very best I get from a mesh point is between 130 and 160. Same device to base station is 300+.
UI-Gunars last edited by
@andres-betts Hi Andres! In lab tests we can get close to 800 Mbps on the router over Wi-Fi, so the hardware potential is there. We need to tune our firmware.
@ubnt-gunars good to know! Thanks for looking into this. If there was a aay this can be given priority I would be so grateful.
John Wojda last edited by
I too am having a problem. Just bought an AmplifiHD yesterday, I plugged it in, updated to the current firmware and was only to get 850mbit (I'm on WOW's Gigabit) one time, and that was with an 80ms ping, the other 7 or 8 speed tests I tried I couldn't break 350mb, so I plugged in my Orbi and the speeds went back to the 800s.
This morning I went and plugged the Amplifi back in and I had consistent 9-10ms pings and averaged in the 900 mbit range! GREAT!!! However just now I ran a few more speed tests (couple hours later from this mornings tests) and now all my speeds are back down to the 300 range.
My internal wifi speeds are bad too. with my previous Asus router and Orbi I could get about 60-70MegaBytes / sec transfers from my NAS (bonded gigabit) to my laptop wireless, the Amplifi is about 20-30MegaBytes/sec.
I was all set to box up the orbi and return it, but this is making me question that.
PS: sorry, I didn't mean to hijack the thread.